Placement of Brace Buttons

Buttons should be aligned with the pleats,
marked by the red dots

Now that we've covered off that braces should be worn with buttons (see previous post), where should the buttons be placed?

Placement of buttons is critically important to wearing braces. It determines where the brace straps lie and the line of the pants. In fact, you can probably notice a man wearing braces with a suit even when he has his jacket on, by the way the pant line cuts down the middle (when worn with pleated pants).  Buttons that are too close to the mid-section are uncomfortable and get in the way; too far apart, and the buttons do not adequately support the pleat and pant lines. This is true for both the front and back of the pants.

Alan Fusser correctly notes that there should be four buttons in the front: one over each of the main pleats, the other two just forward of the side seam. Depending on the brace connection, I find that 3.5-4 inches from pleat to side seam is comfortable and provides superior support. In the back, there should be two buttons (for Y-back and X-back style), equidistant from the center of the fork of the braces, so it falls naturally. Here it depends on the style of braces you plan to wear – Y-back braces require buttons closer together (about 2 inches on each side of the middle seam) while buttons for X-back braces should be spaced a little farther apart. I’ve found that 3-4 inches on each side of middle seam is comfortable. There is also a variety that has 4 buttons in the back for X-back braces.

Button placement in the front
The placement of the buttons in the front of the pants is critical to supporting the line of the pants. To illustrate Alan Fusser's advice above, here' are 2 pictures:

 The one on the left has the buttons too close to the middle and not supporting the main seam. The one on the right has the buttons way over to the side, supporting the side seam, but the main seam will sag. Therefore, there is a balance that should be achieved. The main seam is most visible and should be supported first, followed by the side seam. Depending on the size of the pants, you may be able to support both the main and side seam with the braces.


Inside or outside?
The buttons may be sewn inside or outside the waistband, depending upon personal preference. Historically, when vests were worn and concealed the braces, the buttons were sewn on the outside. When people started shedding vests, the buttons migrated to the inside. I personally don’t notice a difference when wearing braces, but you may. As for fashion, I think it can be very stylish to display the brace buttons on the outside of your pants or skirt. However, it can be distracting if the pants also have belt loops.

Belt Loops
Pants or skirts to be worn with braces should not be worn in conjunction with a belt. You don’t need both a belt and braces to perform the same function of holding up your pants (or skirt). Therefore, the wearer must decide how to wear the pants – with braces or with a belt. Pants to be worn with braces should not accommodate a belt and so should have no belt loops (or be removed). Pants to be worn with braces should be a little larger at the waist so that they are actually "suspended" from the shoulders. 

The skirt on the right is too large
around the waist; on the left is
perfect size.

The front side of the skirt from the left picture displays
the correct waist size, button placement and suspension
(unfortunately the brace material is deteriorating)

I understand that the majority of suit pants and skirts are made ready to wear, and the majority of society does not wear braces. As such, the majority of pants and skirts come with belt loops, and so people leave them on when wearing braces (even with buttons). However, if you are to be functionally correct, the belt loops should be removed. Think of it like wearing a cuff-link shirt with no cuff-links – you know something’s missing. 

Don't follow his example. Not only does he have belt loops, he also has poor button placement - they are not aligned with the pleats and are too close to the center.

Types of buttons
While we are discussing button placement, we should also discuss buttons for braces. Brace buttons should:

• have 4 holes (rather than 2) to anchor the button to the pants. This provides proper support.
• be cone-shaped on the side facing the brace strap. If a straight button is used, the button threads will start to dig into the leather brace strap when tension is applied and cut it from the button hole on the brace strap. Eventually, or with enough force, the button hole will break open and the braces will lose tension. The button may still be attached, but the brace strap is unusable as the button hole is ripped open. To avoid this situation, cone-shaped buttons should be used. 
• match the inside lining of the pants. If the buttons are on the outside, feel free to sew on decorative buttons or ones that match the pattern.

A word on buttons popping off
One of the chief advantages put forth by the proponents of clip-on suspenders is that there is no buttons popping off – once a clip snaps off you can easily reattach it. While this is true, it misses the point of using buttons for braces and the style benefits of buttons. 

Significant stress is usually needed to
pop-off buttons

Balance is needed when determining the strength of the button threads to anchor braces – too strong and the brace strap will break from pressure resulting in the braces not being usable, too weak and the button threads will be constantly failing and buttons popping-off, resulting in the need to sew on the buttons. Contrary to belief, buttons popping off is not poor design. In fact, braces are attached with buttons to allow them to pop off under significant stress to save the brace strap button holes and ultimately the braces. One would rather have a popped button than a broken button hole on the brace strap which renders the braces unusable. Therefore, try to use the right thread weight and strength when sewing on the buttons. I’ve generally found that about 3 threads through each button hole is sufficient.

The brace buttons that generally pop off are the back ones. This is because they experience the most strain in tension. Consider this turn of events:

The man has lost both his back suspender buttons and is unable to use his braces to hold up his pants. However, his braces are in tack, so all he needs is new buttons to be sewn on. Also notice the durability of the left button - only popping off after significant pressure. So unless someone has the braces in their firm grip and pulling them, they generally do not pop-off. The fact is, clip-on suspenders would have snapped off a lot sooner than the buttons popped off. Therefore, use buttons whenever possible.

Here's a cute poem:

Roll-over

When sewing on buttons on the inside, the braces will pull-up the pants (doing their assigned task), and you may get the dreaded roll-over. 

To avoid this, make sure the button threads are sewn almost completely through the pants and get the majority of the pant lining. It may also help to put the button on the upper portion of the pant lining. You may also consider sewing completely through the pants using the same color thread as the pant material. Or sew the buttons on the outside...

Gary Cooper displays excellent button placement and style.

If there is one area that separates newbie brace wearers from seasoned professionals, it is in button placement. An expert brace wearer can tell the moment they see someone wearing braces if they are worn correct or not. So take these notes to heart next time you sew on buttons.

Discussion time:

• Where do you find button placement to be most comfortable?
• Do you prefer buttons on the inside or outside?
• Do you find your buttons are popping off?
• Have any humorous stories of buttons popping off?

Note: all photos are used solely for non-commercial use and to illustrate braces in fashion. No plagiarism is intended.